Woodworking Talk banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 38 Results
  1. Power Tools & Machinery
    Hello, I currently use a Kobalt portable tablesaw (Lowes). I have a hard time keeping everything square. I was thinking of upgrading to a Grizzly table saw (G0771Z). I chose this brand because of the price point and the ability to make it somewhat movable with a base. I have been woodworking...
  2. General Woodworking Discussions
    I just received my Harvey table saw HW110S-36P on 10/5/23. The pallet was damaged, while unpacking the saw I noticed nuts, washers & bolts falling out of the packaging (no big deal) however, I started noticing more and more cosmetic damage to the saw e.g deep scratches, chips on the paint, some...
  3. Power Tools & Machinery
    I bought a Delta 34-806 tablesaw from a place going out of business. It is a 5 Hp, 3 ph unit (Delta Motor 87-369). I ended up getting a VFD in order to run it on my single ph power at the house. It worked for a while. Now the when I hit the start button the motor just clicks and then I get an...
  4. General Woodworking Discussions
    I have a local lumber store that sells some high-quality 2x4x8s for reasonable prices and I was hoping to rip them down and turn them into flooring planks for my house. I figured I'd square up the 2x4s and then rip them down to 1/2 inch thick by 3 inches wide. Then cut to arbitrary lengths and...
  5. Member Classifieds
    Jet 708492k JPS-10TS 10" Proshop Table Saw + 30" Fence Jet 10" Blade Diam, 5/8" Arbor Diam, 1 Phase Table Saw 1-3/4 hp, 27" Wide, 115 Volt, 3-1/8" Cutting Depth Blade Diameter (Inch) 10 Arbor Diameter (Inch) 5/8 Maximum Cutting Depth (Inch) 3-1/8 Located in North Chesterfield, Va.
    $1,250 USD
  6. Member Classifieds
    Jet 708492k JPS-10TS 10" Proshop Table Saw + 30" Fence Jet 10" Blade Diam, 5/8" Arbor Diam, 1 Phase Table Saw 1-3/4 hp, 27" Wide, 115 Volt, 3-1/8" Cutting Depth Blade Diameter (Inch) 10 Arbor Diameter (Inch) 5/8 Maximum Cutting Depth (Inch) 3-1/8 Located in North Chesterfield, Va.
    $1,250 USD
  7. Power Tools & Machinery
    Hi, I bought a used craftsman tablesaw model number 113.298840. I had to adjust the trunion because my blade was not parallel to the miter guage. After I did that the belt was very loose on the pulleys. I bought a new belt and adjusted the motor according to the manual. I tested it by pinching...
  8. General Woodworking Discussions
    I have my dad's old Rockwell/beaver 9" table saw, It has a 3/4hp motor on it. I am wondering if I can get away with the 8" blades or should I just be safe and get the 6" blades?
  9. New Member Introductions
    I've been pounding my thumb since an early age but have all my digits, so far. Happily retired and own an old house built in the late 1870s. It was gutted out when purchased and I'm playing as time permits until it's gardening time. I've spent a number of years in Rhode Island wearing a nail...
  10. Power Tools & Machinery
    Hi, I was wondering if anyone had experience with this model of table saw? I have the opportunity to buy one for $800. It comes with a upgraded 5hp motor, the original motor as well, a Pro-rip/Evolution1 mirco-adjustment fence by Voss Technologies, delta tenon jig, cross-cut sled, and miter...
  11. Power Tools & Machinery
    I have a 20 or so year old 10" Delta contractor's saw, #34-444, 52" unifence. It's been adequate and a good workhorse, but I've had problems for years with binding when raising and lowering the saw, and particularly when angling the blade. I usually clean it out, spray some silicone, and deal...
  12. General Woodworking Discussions
    My "Workspace" is an old 1930/40 outbuilding that i believe was used as a carriage house, however, they had the space 14x18 paved with a drain angle, looks like a 5-10 degree from the front all the way to the back, I have a Delta contractor saw and I want to build a workbench/extension table...
  13. Dust Collection
    So recently I got an old Craftsman 113.19063. I haven't gotten a chance to use it because we got evacuated during all these dumb fires in Cali. Anyway, I am going to build an ~4x6 table/stand/cabinet/outfeed table that it sits on/in and that I can store tools etc in. I have a small single car...
  14. Power Tools & Machinery
    Very please with how this turned out. It's such a major upgrade from my portable Skil tablesaw.
  15. Power Tools & Machinery
    Hello, my father passed away recently, and my family is cleaning out our big storage unit. We need to get rid of these power tools, and I would like to know if they are things that I can post on Craigslist for a price or just give away. I'm sorry for the picture quality. I wasn't the one who...
  16. Power Tools & Machinery
    I've been on the stinkin' internet for hours trying to figure out what to do about my 113.12173 Craftsman table saw motor. I am trying to replace it, but can't find a specific comparable motor. I can run the table saw, but I'm pretty stupid when it comes to fixing it! Any thoughts on an...
  17. Power Tools & Machinery
    Greetings, I am re-installing a Vega 26” utility fence on my Bridgewood contractor’s saw. Unfortunately, I can’t locate the assembly manual for the fence and don’t recall how the rear rail, which is attached to the back of the saw with 2 adjustable bracket’s goes together. Would anybody have a...
  18. Power Tools & Machinery
    I just purchased a Powermatic table saw model 411. I got it for $30 on craigslist as a sper of the moment decision. I was using a friends craftsman portable table saw. I figured it would be worth the risk of only $30 to have my own saw. It has a 13amp motor, aluminum top with 2 wings. The...
  19. Power Tools & Machinery
    I am new to woodworking. I just purchased a DEWALT DWE7491RS job site saw. This is just a stopgap until I can get a cabinet saw. I realize this will never be as good as a full-size cabinet saw. Being a job site saw it has a painted cast aluminum table top. I noticed on my very first project that...
  20. New Member Introductions
    Hello fellow woodworkers! Earler this year I made a table saw from a circular saw. Now I'm not completely satisfied with the cutting depth, so I may wanna change the blade to a larger blade. This means that I have to remove some of the parts on the table saw, which I don't think is a big...
1-20 of 38 Results
Top