Woodworking Talk banner

table saw

  1. Power Tools & Machinery
    I have an old craftsman 10" contractor table saw. Picked it up, cheap, on FB marketplace, to replace my even crappier old craftsman portable table saw, as the fence was worse than useless, it was dangerous. The angle adjustment, however, is the worst design possible. Pure friction!!! Who the...
  2. Power Tools & Machinery
    I have a Craftsman 152.221140 hybrid saw. It has the main table area plus one extension on each side per standard. Is it possible to add more extensions? If so what should I look for?
  3. Power Tools & Machinery
    My new used table saw has cabinet mounted trunnions so to adjust the blade runout you move the table. The blade is a little less than a 64th (64th is the smallest measurement I have) closer to the miter slot in the rear than the front of the blade. I followed the instructions to loosen the bolts...
  4. Power Tools & Machinery
    I am very new to woodworking. I want to buy a table saw that I can use to make dado cuts. However, I have heard that some saws cannot have dado blades installed in them. Is this true? And if so, how do I know which saws will take a dado blade set? I'm hoping to buy the saw used to save a bit of...
  5. Power Tools & Machinery
    Hi all, I recently bought a used Craftsman 10" bench saw (model no. 113.29943) and have had trouble getting it to work. I'm fairly new to both woodworking and machinery, so I'm not particularly knowledgeable when it comes to either. I was hoping I could find help troubleshooting on here and get...
  6. Power Tools & Machinery
    Just wanted to share that I upgraded my cheap-o 10" tablesaw to a used Ryobi BT3000. I realize that on the scale of awesome woodworking bench saws, this model is still beginner-level, but it's better than the cheap plastic one I was using before... and I still have my smaller 7-1/4 bench mounted...
  7. General Woodworking Discussion
    Super Croscutt for table saw can use for Tapering, jointing, make circle, table sled, miter and bevel. 6 in 1 function on 1 jig very usefull and safe storage for organize because can knock down for all part. I made this from HMR material coz very flat material, solid and durable (waterprof)...
  8. Power Tools & Machinery
    I just purchased an older Craftsman 113.29960 contractor table saw. I needed to upgrade from a benchtop table saw in order to get more consistent & accurate cuts as my carpentry side-job has grown. I am replacing some older parts that have worn out (pulleys & belt) but everything else is in...
  9. General Woodworking Discussion
    This is multi jig for table saw can use for Tapering, jointing, make circle and table sled, 4 in 1 function on 1 jig very usefull and safe storage for organize because can knock down for all part. I made this from HMR material coz very flat material, solid and durable (waterprof). Very safe...
  10. Power Tools & Machinery
    So a 1.5 Hp Unisaw has popped up in my area on the used market for $780 and I'm trying to decide whether or not to buy it. It would be a big upgrade from my current tablesaw... but I'm not sure if the 1.5 Hp motor is worth the investment, especially since it's not an RI bullet motor...
  11. General Woodworking Discussion
    I try make adjustable jig for table saw, can use for any jig combine with T slot. i build from HMR coz this material super flat, solid and very durable (waterprof). This jig can combine with many jig, now i make spline jig, not only that can use for feather board for safety cut without kickback...
  12. General Woodworking Discussion
    This is multifunction jig for table saw, can use for any jig combine with T slot. i build from HMR coz this material super flat, solid and very durable (waterprof). This jig can use for feather board for sacety cut without kickback, bevel cut, tenon and mortise joint. i think this jig can...
  13. Power Tools & Machinery
    Can someone help. My first table saw, its a PM 2000B. The accufence is rubbing against the guide tube when in the unlocked position. It has scratched up the silver strip on the guide tube. This is a new (not yet used) table saw. I called support but they were not helpful. I have disassembled...
  14. General Woodworking Discussion
    So I am brand new and want to setup a workshop in my garage. I am cleaning everything out of my 2.5 car garage that I haven’t used since I moved in and have a ton of space to fill, but I need recommendations on what tools to fill it with. My budget is 1-2K, but I can go up to 3-4. I have a...
  15. General Woodworking Discussion
    How to make DIY Thin Strip Jig / Thin Rip Jig for your Table Saw. Table saw jigs can be used to make woodworking safer and more convenient, this jig can be used to make repeatable thin strips for a variety of builds. I made this Jig for scrap HMR, very cheap and easy for build but very useful...
  16. Power Tools & Machinery
    I'm new to woodworking and looking to build a multipurpose table that will incorporate a bench top table saw into it. I was originally looking at purchasing a Dewalt table saw but I'm afraid their rack and pinion fence system won't work well for incorporating it into a large workshop table. I...
  17. Tips, Tricks, & Homemade Jigs
    I want to cut a slot in piece of alder so I can join a slanted piece sticking out of it, but I don't want to go all the way through. Is it safe to do a plunge cut on a table saw with an angled blade?
  18. Tips, Tricks, & Homemade Jigs
    Hi Guys, this is my version of DIY table saw sled for my Makita Mlt100. I equipped it with a graft for the sawdust extration hose.
  19. Power Tools & Machinery
    Hello everyone! I've been reading this forum for a couple of years now, but hadn't signed up. Recently, though, the bug finally bit me and I decided to go off the deep end into woodworking (my wife says I do that too often with hobbies). I've done quite a bit of home remodeling and have done...
  20. Power Tools & Machinery
    I am close to a decision to purchase the Grizzly G0771Z. My last concern is about weight, specifically how to move it down a short flight of stairs into my basement shop. The Grizzly web site shows the assembled weight at 286 lbs. Same site shows the shipping weight for the big box at 330 lbs...
Top