Woodworking Talk banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-12 of 12 Results
  1. Power Tools & Machinery
    hello friends is the purchase of Parkside wood milling machine POF 1200 D3 at a price of 40eu a hit or not? I recorded one test video. What do you think after all? Parkside Router POF 1200 D3.
  2. Tips, Tricks, & Homemade Jigs
    We just mounted a large wall hanging woodworking project. It is like a big picture. A friend asked me about how I mounted it and I replied with some info and a photo, and I thought I would share some of the lessons I have learned over the years with my friends at WoodworkingTalk. NOTE: By "wall...
  3. Joinery
    Hello guys, Here´s a new video of me making grooves with a router and a guide. A simple tip for begginers. Fui. https://www.youtube.com/watch?v=34V9j9ENgDM
  4. Power Tools & Machinery
    Before I order a custom router bit, I wanted to ping you guys first. I want to create this profile, it’s incredibly small .25 inches high and .5 inches wide. I’ve tried doing it with a roundover to no avail (do both sides then flip it over). The chief issue is that the corners are not the same...
  5. Tips, Tricks, & Homemade Jigs
    I'm trying to route a small slot 1/16" wide, 3/4" long, and at least 3/8" deep. I've found 1/16" bits, but the cutters are not long enough to cut 3/8" deep. Anyone have a source for a longer 1/16" bit, or have a different suggestion of how I could make this type of slot? Thanks!
  6. Power Tools & Machinery
    I have a Bosch 1617EV Router motor in Bosch Plunge Router. I want to use a 5/32 drill on it, but the collet is too big. Do they make collets this small? Regards, Larry
  7. General Woodworking Discussion
    Covering my kitchen cabinets with paper backed teak veneer. I am curious as to which bit would cut the smoothest. I would like to be steered towards brand suggestion as well. I just want the best cut possible. I have purchased a Makita trim router that has a 1/4 collet. Thanks for the help.
  8. Hand Tools
    Hi Fellow Woodworkers, For those of you who enjoyed the First Router Bits Profile Quiz, Toolstoday has prepared a new challenge to test your router bits IQ for your enjoyment. Test your knowledge of router bit profiles by correctly naming the router bits. The Router Bits Quiz 2 can be...
  9. Hand Tools
    Hi - I picked up a used Skil classic router at a garage sale. I brought it home and used it and it works fine, but when I attempted to change the router bit in it I ran into a problem. I loosed the collet as much as it will go and bit still will not come out? I'm not familiar with routers, but...
  10. General Woodworking Discussion
    I ran across this free tool giveaway. Its a nice 50 piece router bit set with cabinet. I thought if someone is interested in adding to their collection this might be a good idea. They draw the winner on the 26th of November. Router bit set giveaway
  11. Design & Plans
    Hello, I'm going try to build a guitar speaker cabinet out of MDF in 3/4 I was going to use Baltic birch but the cost in a little to high for me anyway my question is can rout the edge of MDF board once its all together using a round over bit? or will it chip up or splinter? I ask this because I...
  12. General Woodworking Discussion
    Hi Guys, Don't get over here much...spend quite a bit time in the DIY hang out...but I'm hoping someone can help or point me in a positive direction... I have a profile of a piece of trim that I picked up at the local BORG...it was jammed in a close-out bin last piece, no labels, just $X per...
1-12 of 12 Results