I hope this is just a noob question. I am hanging shelves on brackets with MDF to be painted. The shelves are 11.5 in wide and will be mounted inside a nook and I want to do miters on the inside corners.
Knowing my walls would not be perfectly square, I measured the angle at 88 degrees. I...
Hi all -
I'm sure this will stir up everyone, but maybe fun for a Monday :)
I have a spot in my basement shop, where I'm building a miter station. In a perfect world, I'd have a 20 foot wall that I can fill up, but it's not reality for me.
Question - For the majority of your needs, is 5ft left...
three 36" t-tracks by two 24" vertical t-tracks '3/4" wide' on 40"x28"x1.125" wood board 'mdf or blockboard or plywood'
bench dog holes size is 3/4" and are of two groups; dig holes are vertically spaced by 3" measured from the center of the middle t-track and are horizontally spaced by 5" for...
Novice here. I'm trying to add some cove molding but having a tough time figuring out the cut for the turn on my stairs. Please see attached photo. Can anyone here offer some guidance on how to finish this off? Huge thanks in advance!
I'm new here, and am hoping someone can give me some help.
My Father in law passed away, and one of the things he left me was his very old table saw. It is small and works fine and served him well for many many years, but is missing the miter gauge. After going through everything in the...
Hey guys, I bought a DWS780 12'' and I wanted to treat it with a good blade, but might have made a mistake. I bought a Festool 12'' 100T 0.120'' (so full kerf) miter saw blade. I do a lot of moldings and the blade is magnificent, the end grain is smooth as if I had sanded it and it fixed my...
I am cutting plywood for a large plywood wood box and I am mitering the edges at 45 degrees.
I have my table saw set at 45 degrees but I am sort of confused as the best way to make sure I make the cut in the right spot.
Is the best way to go about this to make a test cut on a similar...
I am building a bird feeder and used two 30° miter cuts on the top that meet like a triangle. I thought a 30° bevel cut would work for a roof... however it did not. I attached a very rough sketch.
How do I find the angle to make my two bevel cut to fit the miter cuts?
Thanks for your help.
I'm sure this topic has been done a million times but I've finally out grown my throw together miter saw stand that just sits on sawhorse. I know there are a million ideas out there but I would like to see pictures of yours or your favorite "portable" (preferably on wheels) miter saw stand (or...
I am wanting to make a pedestal similar to this one http://www.bausmanandcompany.com/images/uploaded/6323-44611.jpg
I am fairly new to woodworking and need help on how to make the miter cuts, and fit them together for the main pedestal part of this design.
My question is, after I make the...
Hey there! I a beginner and I have been researching sliding miter saws for a while, but am having a hard time pulling the trigger on purchasing one. Granted, I am a DIY'er and hobbyist and I definitely have a lot to learn. But I don't want to get stuck with a cheap miter saw and essentially get...
I have a follow-up question to my past post on the Bedpost Glue-Up.
When creating the miters on the post (four faces, mitered to a 3" square, filler block down the center, would method would you use to strengthen the migher joint? The options are:
1) Lock Miter Bit (have heard this is a...
For those of you that are following the accessories for the Super Sled, there's a new video available that shows how to build the mitering system.
Here's a link to the video:
Here's a few pictures of the new setup:
How do I miter (at 45 degrees) the edge of the whole width of a 3/4 inch thick, 8 feet long ,2 feet wide sheet of plywood?
I only have a crosscut saw, and a jigsaw (I tried but it wont cut)
, and a block plane NOT a chamfer plane
I plan to make a table en carcasse, made completely out of...