Woodworking Talk banner

hinge

  1. What type of hinge is this?

    General Woodworking Discussion
    Heya, I need a little expert help here.. I need to replace the hinges on this cabinet door on this 15 year old desk of mine. I've googled and read quite a bit on hinges but I just would like it to work for the door. I'm not sure of what it is... so your help is greatly appreciated. I...
  2. Semicircular Butler Hinge Jig

    General Woodworking Discussion
    Hi. I couldn't find this in a search of the forum. I like working with butler hinges that at the opposite ends of the center hinge are semicircular. Which quality brand I use is not much concern: I'll use any competitively priced one. Does anyone know of a router jig designed to work with a...
  3. Mortising a 270 non mortise cabinet hinge

    General Woodworking Discussion
    Building a game coffee table with top split in middle and halves are opened to game surface. The option I desire is to use them as leaves, with an option to have the doors rotate completely down, perpendicular with top. First question is about options on 270 hinge. I want to recess any hinge...
  4. replacement hinges for medicine cabinet

    Trim Carpentry & Built-Ins
    I have a 10 year old good quality medicine cabinet but one of the hinges gave up the ghost and the other isn't far behind. Trying to find replacement hinges has become quite the task and I was hoping someone here could help. The cabinet is a two hinge single door weighing 19 lbs with mirrors on...
  5. Help identify old cabinet Hinge

    General Woodworking Discussion
    Hello, I'm currently searching for some specific hinge that seem to just not exist anymore. I went to a lot of local store and searched hundreds of pages on different canadian seller and I just can't seem to find anything close to it. There's no model number or even any writting on them so it's...
  6. An unfolding wooden cube help

    General Woodworking Discussion
    Hello, This is my first time posting on this website and if I'm doing anything wrong, please let me know. I'm trying to a build a hollow wooden cube (about 5 in on each side, so pretty small) using 1/8" thick wood. While the cube is sitting on a table, I would like to be able to pull one...
  7. Tension/Torque/Torsion Hinges for Angled Sink Mirror

    General Woodworking Discussion
    HELP PLEASE: Tension/Torque/Torsion Hinges for Angled Sink Mirror Our master bathroom has an angled mirror above the two sinks. The mirror is 12.5 inches tall, but spans the full width of the counter (66.5 inches). Above the angled mirror is a window, which explains why the builders could not...
  8. Hinge Help Please! Type?

    Design & Plans
    Hello friends! As you can see from the picture, I'm wondering if anyone knows of the type of hinge I would need for this peculiar movement? The picture is a side view, of a door that opens downward. Any insight or specifics would be greatly appreciated. Colin
  9. Bed Design Help//Unity 3D Model Available

    Design & Plans
    I'm looking for a LITTLE help on how I can get around making a drawer for a bed that comes out and up like a lateral hinge drawer. I have made a schematic on Unity3D if anyone knows how to get it to work ( I sure can't)
  10. Help me find this type of hinge.

    Joinery
    I am building a cabinet very similar to the pictures I will link to. I am trying to determine what type of hinge is being used to let the door pull/tilt out. I have tried several but have not worked that well. But I have never been able to find the exact one that cabinets like this use...
  11. alternative to sugatsune SMH-40/SN

    General Woodworking Discussion
    i'm looking for some tabletop hinges; something that's flush when open and can fold up past 90degrees. i'm wanting a satin nickel; stainless steel would work; not interested in brass. i really like the look of this hinge: http://www.thehardwarehut.com/images/cabinet_hinges/sug-smh-40-sn.jpg...
  12. Double action hinge confusion

    General Woodworking Discussion
    For the life of me, I can't figure out how this double action hinge is supposed to work (top hinge in photo). It is supposed to allow a panel, such as a door, to swing both directions. Out of the box, it only has 1 place it pivots, so I assume that I am supposed to take it apart and reassemble...
  13. 35mm Euro Hinge with 7/8 overhang

    General Woodworking Discussion
    I made my doors a little large and am not making heads or tails of the hinge specs. (first time with the euro style) I like the 120* opening and can not tell if one is available in a 7/8" overhang. Before I start trimming them down can anyone tell me if I need to? Thank you
  14. Question about what type of hinge I need

    General Woodworking Discussion
    I'm working on building a small box and I need a hinge, but I'm not sure what type of hinge that would be. I'm looking for a hinge that mounts to the outside of the box so that the lid is closed when the hinge is at 90° and when the lid is open, the hinge is 180° or 270° (doesn't matter if...
  15. Door question -- Potting Bench Project

    General Woodworking Discussion
    I am making a potting bench for my wife and I have a door question. I've made two doors by butting 7 1x3s together and screwing them together with 2 support boards on the back of each door. It appears the door on the right is to be fitted in a space that is square. The one on the left doesn't...
  16. Beginner's Question: Where's best/cheapest place to buy fasteners and hinges?

    General Woodworking Discussion
    Hello All, Where is the best or cheapest place to buy hinges and fasteners? I'd prefer an online source as I have a desk job, so it's more convenient to order online and in bulk than to use the time I could be in the shop driving around. I just got started with woodworking. I managed to...
Top