Woodworking Talk banner
fence
1-20 of 21 Results
  1. Power Tools & Machinery
    Hello, im new to the forum and I just got a new fence for my table saw and it has this aluminum bar across the top and I was wondering if somebody could tell me what its used for, cause I can't figure it out for the life of me. However, I am new to wood working.
  2. General Woodworking Discussion
    Hey everyone, I'm new to the forum and relatively new to woodworking, but I'm trying to get better and also trying to upgrade equipment so I can have a little more faith in the tools I use. I'll try to keep this brief, but I'm sure I'll ramble. I have had a Ryobi table saw for several...
  3. Power Tools & Machinery
    Quick backstory: I'm relatively new to table saws and I feel a little overwhelmed looking at the options. I am building custom cabinetry (kitchen and bathroom) and so I am handling large plywood sheets regularly. The two things that are most important to me are: 1. An extension if possible to...
  4. Power Tools & Machinery
    I would like to know if anyone has ever put a Vega U26 fence on a Rockwell 9 inch contractor saw. The cast iron table is 15 in wide X 22 deep. It is 30 inches wide with aluminium extension wings. The manual says you need holes that are 16 on center with the right hole being 8 inches to the right...
  5. Power Tools & Machinery
    My DeWalt 7490X table saw fence is stuck and will not flip over. It was working just fine and now it's stuck. Any ideas?
  6. Power Tools & Machinery
    Greetings, I am re-installing a Vega 26” utility fence on my Bridgewood contractor’s saw. Unfortunately, I can’t locate the assembly manual for the fence and don’t recall how the rear rail, which is attached to the back of the saw with 2 adjustable bracket’s goes together. Would anybody have a...
  7. General Woodworking Discussion
    I need help. I became an owner of a Uniplane yesterday, purchased from Craigslist. I should have gone over the unit more thoroughly before purchasing. I cleaned it up today to find that the screw shaft's v-groove is hosed (set screw binds when turning the adjustment knob) and the in-feed...
  8. Power Tools & Machinery
    I've been a lurker here for while and I finally decided to post with a question. I've owned a Craftsman hybrid saw for a few years now, the #21833. It's served me well as I began my foray into woodworking, building some shop furniture, swingset equipment, and even a built-in home office. I...
  9. Power Tools & Machinery
    hello, I moved to live in thailand, and here table saws are either crap low quality or overpriced high end ones! I always wanted to buy the ridgid r4512, and even if ridgid have business here, they don't sell their table saws. After long researches I finally found the exact copy (coming most...
  10. Power Tools & Machinery
    Does anybody know if the fence for the PM 66 works with the PM 65 table saw? Thanks, Chuck Barnett
  11. Joinery
    Hello guys, Here´s a new video of me making grooves with a router and a guide. A simple tip for begginers. Fui. https://www.youtube.com/watch?v=34V9j9ENgDM
  12. Power Tools & Machinery
    Looking at buying a shaper. Grizzly 1035 0r 1026 The fences look to be cheap. 1. Alternatives to the two shapers I mention here with better features/fence? 2. If I get either of the two Grizzly shapers is there a micro adjust aftermarket option?
  13. Power Tools & Machinery
    Greetings, I'm hoping that someone here can provide some insight on my current dilemma that I am wrestling with. I want to know what other people's experiences have been. I have an Old Craftsman 113.***X table saw that I got off of CL for 50 bucks almost 2 years ago and I am now fed up with it...
  14. Power Tools & Machinery
    Hi Everyone, I was lucky enough to stumble across a steel city industrial fence however i am missing the rail set for the fence. Does anyone have the rail set they would like to sell that would work for this fence, or have any advice on where to get one? I have talked to a few distrubutors...
  15. Power Tools & Machinery
    Hey all, has anyone put a t-2 or other aftermarket fence on the t2 yet? My R4512 will be arriving today, its a replacement from TTI because of my nightmare R4511. i've got a delta T2 so just thought id ask if anyones tried replacing the fence on it yet.
  16. Power Tools & Machinery
    I have a 25 year old Delta 62-044 contractors table saw that works perfect. I am looking for a fence that is accurate and firm. What do you recommend? I am up between the Vega Utility 26 and the Shop Fox W2005. I looked at the Beisemeyer but don't think that I am getting much more for...
  17. Power Tools & Machinery
    My old Delta table saw has an old tube style fence. The fence rides on tubes on both sides of the table. It works, but I don't trust this fence without checking it for square after each adjustment. This is just way too much of a PITA. :wallbash: I have been toying with the idea of a...
  18. Power Tools & Machinery
    Hi everyone, I would like to get your thoughts and suggestions on an extended fence for my tablesaw. I'll be building a table to set my little table saw in in here in the future but I'm stumped on the fence. The fence that comes with it is pretty much designed just for the top itself and not...
  19. General Woodworking Discussion
    I'm a pretty thrifty guy -- putting it nicely. I've got about 20 line posts that need replacing - two-rail. So when I found a place within two hours of my home that sold locust split rail line posts very inexpensively, I thought it would be worth giving them a call. Turns out they're already...
  20. Power Tools & Machinery
    The left and right fences on my Ryobi (cheapie) miter saw are slightly out of alignment. This is a the typical one-piece fence. I've squared the saw blade to the left fence, but would really like both to be co-planar. Any ideas?
1-20 of 21 Results
Top