Woodworking Talk banner
delta
1-20 of 39 Results
  1. Power Tools & Machinery
    Newbie here, though been WWkng since the 60's. I recently had to replace the tensioning rod on my Delta BS, now I can't get it to tension properly according to the indicator. Yeah, I know indicators are not very accurate, but it gets me to a starting point. I'm thinking I did something wrong...
  2. Power Tools & Machinery
    I have a 20 or so year old 10" Delta contractor's saw, #34-444, 52" unifence. It's been adequate and a good workhorse, but I've had problems for years with binding when raising and lowering the saw, and particularly when angling the blade. I usually clean it out, spray some silicone, and deal...
  3. Power Tools & Machinery
    Hello, this is my first post, thank you for having me. Looking forward to contributing and learning. I recently started the wiring of an older Unisaw and have run into an issue with the switch. I cant seem to make head or tails of it but, in the end need to get it wired. Any help would be...
  4. Power Tools & Machinery
    I'm restoring a floor model Rockwell drill press model 1124 which i am pretty sure its almost identical to the 15-081. This was a barnyard machine. Covered in grime and rust, and not taken care of well, at all. The table was broken and bolted to a janky weld up job, among other half-a**...
  5. Power Tools & Machinery
    I am looking for a kind soul who owns a Delta Saw with a model# 62-044 motor. I purchased a used saw with this motor, and found that it had one of the capacitors blown. I used the capacitor model # to order a replacement, and it worked for several minutes until it went "pop" and blew the new...
  6. Power Tools & Machinery
    I have a Delta contractor saw which I bought back in 2002 or so. I ground the tip of my finger off with it a few months ago and decided to invest in a SawStop. I have a buyer interested in the old Delta but I'm not sure what its worth. Any suggestions? -32" Biesemeyer Fence -1.75 hp / 115v...
  7. General Woodworking Discussion
    Hi all. I am looking for advice on a new (to me) table saw that will be my first stationary saw in my shop (garage). I am looking to buy used from CL and have been looking at a few models such as the ridgid R4512 (shying away due to the alignment issues with the weak trunnions). I am looking to...
  8. Power Tools & Machinery
    I've been looking to upgrade from an old Harbor Freight 10" miter that has way outlived its purpose and was looking at all of the latest and greatest miter saws out there. Originally I was leaning towards the Dewalt 780 as it seems to be one of the best reviewed for the price (Kapex is out of...
  9. Power Tools & Machinery
    Hi Guys, I have my dads only 1957 ish era delta rockwell 14in band saw. its in great shape. The bearing right behind the blade has gotten old and is locked up. I am having issues finding a replacement for it. I've uploaded a picture of the bearing in question. On the bearing itself it...
  10. New Member Introductions
    Hi, I'm new here, and am hoping someone can give me some help. My Father in law passed away, and one of the things he left me was his very old table saw. It is small and works fine and served him well for many many years, but is missing the miter gauge. After going through everything in the...
  11. General Woodworking Discussion
    I received this lathe last week as a gift. I am super excited about this but i'm having trouble identifying the model/specs. The serial number is 53-7452. Everything except a couple of handles on the tail stock are functional. Once I can identify it I can start order or fabricating parts for...
  12. Power Tools & Machinery
    I picked up this Delta Milwaukee bandsaw today, my first and only bandsaw, and have a couple of questions. In the 3rd image you see the gap between the cover plate and the body? Is that natural? Dust escape? The 4th image is the plug for the motor. Wtf is up with that, what I assume is some...
  13. Power Tools & Machinery
    Hey everyone, I picked up an *old* Unisaw over the weekend. Serial number dates it back to 1948. When I took it off the trailer, I found a part sitting on the moving blanket. The problem is that I don’t have a clue where it goes. I have looked through the part diagram, but it lacks the...
  14. Power Tools & Machinery
    I have a Delta TS300 that the fence assembly was lost during a move. Every site I check says the part is no long available. What do you suggest? Is there another one that is captable? I hate the idea of having to toss the saw. Is there some kind of cross reference for parts that I can check?
  15. General Woodworking Discussion
    I have an 8-year old Unisaw with a 3hp motor. I notice excessive vibration in the blade. The saw is on a slab, and level. I know the bearings are sealed for a lifetime. So--any suggestions on how to minimize this vibration?
  16. Power Tools & Machinery
    Hi all, I have a Delta 36-600 10" table saw. It uses a notched belt ("timing belt") with matching teeth on the drive shaft so it cannot slip. When this saw starts up it comes to full speed in about 1/2 second. The inertia of the arbor and blade puts a huge strain on the belt (and other...
  17. Power Tools & Machinery
    Hello Everyone, I'm new to this forum so I appreciate the help. I need help pricing out a few items. The first being a Delta 16" Band Saw (Model 28-560), good condition with extra blade. It is on the original stand as well. I've read around that $500 is a good asking price but wanted opinions...
  18. Power Tools & Machinery
    As many of you know I am in the process of restoring a 1955 wood cutting band saw. Parts of it are cleaned up and ready for paint so I am wondeering what you folks use for paint. I know Rustoleum seems to be popular on another forum I belong to. Sherwin-Williams seems to be another. What do most...
  19. Power Tools & Machinery
    Hi all, I am restoring or refurbishing a vintage Delta 14" band saw and need some advice on bearings. I am referring to the bearings in the upper wheel and on the lower shaft. Where do you get your bearings and do you have any idea what numbers I would need to order. Any help appreciated...
  20. Dust Collection
    Hello all, I'm posting this in a wood working forum because it seems that you guys have much more knowledge about dust collection than anyone else lol. We are a computer shop in Michigan. We have built a homemade "dust out" station for dusting out computers. It is powered by a Delta 50-760...
1-20 of 39 Results
Top