Woodworking Talk - Woodworkers Forum - View Profile: Tool Agnostic

Tool Agnostic Tool Agnostic is offline

Senior Member

  Statistics

Total Posts
Total Thanks
General Information
  • Last Activity: Today 11:44 AM
  • Join Date: 08-13-2017

  Friends

Showing Friends 1 to 1 of 1

  Mentions

07-20-2019
11:18 AM - Tool Agnostic mentioned woodnthings in post Table Saw Blades
...blades mentioned by woodnthings are not recommended ...
11:05 AM - Tool Agnostic mentioned gmercer_48083 in post Planer Knife Bevel
...t look like the one gmercer_48083 showed in his photo,...
07-14-2019
12:16 PM - Tool Agnostic mentioned epicfail48 in post Making Cutting Boards
...or the reasons that epicfail48 stated. I didn't ...
07-11-2019
11:54 AM - Tool Agnostic mentioned GeorgeC in post "Scary sharp" on Melamine?
...." I agree with GeorgeC's suggestion: Go to ...
07-05-2019
09:36 AM - Tool Agnostic mentioned Frost in post Large Shaker Style Cabinets
The photos from Frost helped me follow thi...
07-02-2019
07:56 AM - Tool Agnostic mentioned John Smith_inFL in post Sycamore
John Smith_inFL is right. Wood darke...
06-22-2019
09:54 AM - Tool Agnostic mentioned gmercer_48083 in post Chisel bevel thickness
... gift, etc. Unlike gmercer_48083, I am NOT impressed ...
06-10-2019
06:11 PM - Tool Agnostic mentioned FrankC in post Leveling Table Saw: Where to Find Good Local Straightedge 24, 30, or 36 inch?
... way more time than FrankC would have considere...
06-09-2019
12:03 AM - Tool Agnostic mentioned RickKr in post Finessing Dado Slots to 6mm
... The problem that RickKr noticed is that many...
05-29-2019
11:11 AM - Tool Agnostic mentioned unburled in post 90 deg vs bevel blade alignment on table saw
... one statement from unburled that is accurate. Wi...
05-26-2019
11:46 AM - Tool Agnostic mentioned cpandzic in post Used craftsman table saw
...respond now. I hope cpandzic shares the final out...
05-21-2019
09:10 AM - Tool Agnostic mentioned woodnthings in post Sanou K12-125, 125 mm 4 jaw chuck
The link that woodnthings posted above is the ...
05-19-2019
08:43 PM - Tool Agnostic mentioned mugginsville2000 in post Woodworker level 2
...post the links, but mugginsville2000 may be looking at vi...
05-05-2019
10:12 AM - Tool Agnostic mentioned 27207 in post Y'all are horrible people
Everyone experiences the w...
04-26-2019
01:39 AM - Tool Agnostic mentioned nckheinrich in post Theory behind this accident *GRAPHIC*
...ad. I hope that nckheinrich takes the time to th...
04-14-2019
11:38 PM - Tool Agnostic mentioned justdraftn in post MC Escher checker board
... I was joking about justdraftn trying to trademark ...
11:38 PM - Tool Agnostic mentioned Mikhail2400 in post MC Escher checker board
...means. :vs_worry: Mikhail2400 explained it well. T...
04-12-2019
10:39 AM - Tool Agnostic mentioned NoThankyou in post Opinions requested re: small crosses.
...eat. I agree with NoThankyou. Don't overthink thi...
04-10-2019
02:49 PM - Tool Agnostic mentioned johnep in post Ballet barre DIY installation onto partition wall
...proved invaluable. johnep Clarification: When...
02:34 PM - Tool Agnostic mentioned NoThankyou in post Wrench for Delta Contractor Saw missing -- where to buy it?
...in your post above. NoThankyou tried to help. He ga...

  Quotes

07-20-2019
01:54 PM - woodnthings quoted Tool Agnostic in post Agreed ......
I would not run a miter saw withou...
01:46 PM - woodnthings quoted Tool Agnostic in post OK, you've been warned ....
Warning: The two blades mentioned ...
07-18-2019
02:51 PM - P89DC quoted Tool Agnostic in post Low Cost Latex Paint Sprayer?
That $20 Harbor Freight paint spra...
07-17-2019
05:00 PM - Jlivings quoted Tool Agnostic in post Question on stylus kits
I get my pen kits at Rockler. They...
11:18 AM - DrRobert quoted Tool Agnostic in post Low Cost Latex Paint Sprayer?
I was hoping to spend under $20 if...
09:11 AM - epicfail48 quoted Tool Agnostic in post Low Cost Latex Paint Sprayer?
I was hoping to spend under $20 if...
07-16-2019
09:29 PM - Steve Neul quoted Tool Agnostic in post Help translating measurements (newbie)
Your post reminds me of the thread...
08:09 PM - Steve Neul quoted Tool Agnostic in post Low Cost Latex Paint Sprayer?
Thanks for the suggestion, but it ...
07-12-2019
02:34 PM - NoThankyou quoted Tool Agnostic in post "Scary sharp" on Melamine?
Some time ago, I went to our local...
07:34 AM - landman quoted Tool Agnostic in post 14 keepsake boxes
Which one will be mine, Uncle Pat?...
05:19 AM - twedlake quoted Tool Agnostic in post Do You Use Your Table Saw as a Work/Project Table?
Do you use your table saw as a wor...
07-09-2019
11:48 AM - GeorgeC quoted Tool Agnostic in post
12:30 AM - Curtislv426 quoted Tool Agnostic in post Sharpening lathe tool Vari-grind question
-> The original bevel angle for yo...
07-08-2019
08:04 PM - Curtislv426 quoted Tool Agnostic in post Sharpening lathe tool Vari-grind question
You changed (or are in the process...
07-06-2019
07:44 PM - PolishX quoted Tool Agnostic in post French Cleat = Nightmare
I am about to launch a French clea...
07-05-2019
12:02 PM - TwelveFoot quoted Tool Agnostic in post Sharpen or Replace Planer Blades?
Does the shifting (or flipping one...
07-03-2019
10:42 PM - epicfail48 quoted Tool Agnostic in post Do You Use Your Table Saw as a Work/Project Table?
Do you use your table saw as a wor...
07-02-2019
10:12 AM - brentstanley quoted Tool Agnostic in post Forestry trailer- new toy
Off topic: I may never get over t...
07-01-2019
10:30 AM - Quickstep quoted Tool Agnostic in post Why does gorilla glue recommend moistening?
Clear Gorilla Glue is a silane-bas...
08:45 AM - gj13us quoted Tool Agnostic in post Amana mamba?
Because they are harder to see whe...
 
For the best viewing experience please update your browser to Google Chrome