TomCT2 TomCT2 is offline
- Last Activity: Yesterday 08:40 AM
- Join Date: 05-16-2014
|11:08 PM - TomCT2 mentioned Steve in post Computer help
Steve - yup, it's a browse...
|12:43 PM - Student mentioned TomCT2 in post Please advise a newbie about rail and stile router bits
TomCT2, thank you.
|01:49 PM - Mad mentioned TomCT2 in post Adding Sacrificial Straight Surface to Table Saw Fence: What and How?
...iation extended to @TomCT2, @Tool Agnostic, @Ji...
|12:44 PM - uberspeck mentioned TomCT2 in post Good wood choices for decorative screen wall? (also, first woodworking project!)
TomCT2, thx for the reply! ...
|10:23 AM - Tool Agnostic mentioned TomCT2 in post New Blade for Delta 36-725 table saw question
...ches I note that TomCT2 had the riving knife...
|12:01 PM - Tool Agnostic mentioned TomCT2 in post Sanding Blocks
...ck marks. I like TomCT2's idea of making a s...
|03:55 PM - psaffaru mentioned TomCT2 in post need help -- issues with dewalt table saw
TomCT2 In fact I meant the...
|06:02 PM - CaptainMike mentioned TomCT2 in post Butcher Block Finish
Thanks TomCT2. I was considering j...
|11:59 PM - John_S_804 mentioned TomCT2 in post Craftsman Radial Arm Saw will not elevate
TomCT2: There is another se...
|12:20 PM - ChuckBarnett quoted TomCT2 in post Tablesaw motor tripping breakers
look like it's a smidge too...
|08:26 PM - Mycrossover quoted TomCT2 in post dewalt radial saw
it's likely the grease has ...
|06:28 PM - RustyPlaneWW quoted TomCT2 in post Best Collection System for Thickness Planer?
it's actually a 2-1/2" "std...
|05:27 PM - RustyPlaneWW quoted TomCT2 in post Best Collection System for Thickness Planer?
planners create large volum...
|01:25 PM - BFG-Cabs quoted TomCT2 in post Preventing finger joint blow out?
my bet is the "Backing Inse...
|12:59 PM - FrankC quoted TomCT2 in post Mak'n due w/what you have......
Justdraftn - drop in her...
|09:13 PM - Quickstep quoted TomCT2 in post Check out my bit holder
I presume it's a lazy susan...
|02:15 PM - FrankC quoted TomCT2 in post Drill Press Setup
(floor standing model) I us...
|04:27 PM - sgcz75b quoted TomCT2 in post Adding a “gripping area” to a cutting board
t all the musik about "Dan...
|07:36 PM - unburled quoted TomCT2 in post mobile benches question
another approach is a bench...
|11:40 AM - gmercer_48083 quoted TomCT2 in post Need big time help with small project
Gary - the lifters are suit...
|09:00 AM - Juanitta1 quoted TomCT2 in post Deleted Posts
|08:09 PM - BNB187 quoted TomCT2 in post Garage Door
14' on a table saw is not a...
|09:24 PM - Sleeper quoted TomCT2 in post Recommendations for fitting Screen Door
the redwood may not take pa...
|09:40 AM - Quick Cal quoted TomCT2 in post Delta T3 vs Craftsman align a fence
came with the saw - the bas...
|01:40 PM - dmayo2 quoted TomCT2 in post Porter cable dovetail
this one looks right - http...
|09:10 AM - dmayo2 quoted TomCT2 in post Porter cable dovetail
check your router manual. ...
|08:07 PM - renraw9002 quoted TomCT2 in post Flocking a blanket chest
bad idea. eventually comes...
|11:41 AM - CLS89 quoted TomCT2 in post Router Kickback (Planing Operation)
obviously the depth is vary...
|11:01 PM - Tennessee Tim quoted TomCT2 in post Making Charcuterie Boards Restaurant Safe?
you are concerned about ing...