Woodworking Talk - Woodworkers Forum - View Profile: thenodemaster

thenodemaster thenodemaster is offline

Yay! Finally on Facebook

  Visitor Messages

Showing Visitor Messages 1 to 2 of 2
  1. Big Jim
    09-18-2015 10:34 AM - permalink
    Big Jim
    Squirt a little 30W on the bearing and forget about it! 99% of the time it is an oil shield making the noise. It is rare indeed to ruin a bearing on one of these small lathes. I oil one of my lathes every three or four weeks to shut it up, and it still runs true.
    Big Jim
  2. thenodemaster
    06-24-2015 01:11 AM - permalink
    thenodemaster
    Don't worry! The Dachshund with the framing nailer is a professional!

  About Me

  • About thenodemaster
    Biography
    Work full time. Go to school full time. Own small business part time. Sniff saw dust.
    Location
    BFE Hemet
    Interests
    Wood working, wood turning, CG artwork, R/C helicopters and airplanes, butchering wood.
    Occupation
    Network Administrator, Business Owner, Full time student (MS)
  • Signature
    Dachshunds and pneumatic nailers do not mix. Whiskey. Tango. FOXTROT!

  Statistics

Total Posts
Albums
Visitor Messages
Total Thanks
General Information
  • Last Activity: 05-09-2016 12:56 AM
  • Join Date: 06-14-2015

  Mentions

08-13-2015
02:10 PM - thenodemaster mentioned 44260 in post WoodTurner Pro Software
OK. Thanks, fellas. dirt...
07-18-2015
02:59 AM - thenodemaster mentioned Gary in post Almost...
...some karma points. Gary: I think that that w...
02:59 AM - thenodemaster mentioned bond3737 in post Almost...
...n' on my own, huh? bond3737: nice to know I am i...
07-10-2015
09:02 AM - thenodemaster mentioned Bill Boehme in post Stringy Buffing Wheels
... Really good info. Bill Boehme: I wear a Trend Airs...
09:02 AM - thenodemaster mentioned saculnhoj in post Stringy Buffing Wheels
...eating this issue? saculnhoj: I found out the har...

  Quotes

11-20-2015
08:09 AM - BZawat quoted thenodemaster in post Grizzly lathe
I spent just over $3000 on my G069...
11-15-2015
08:02 PM - Bill Boehme quoted thenodemaster in post Woo-Hoo!!! Getting my new Band Saw Delivered Tomorrow!
?... Anyone know of a place beside...
11-09-2015
07:28 AM - mengtian quoted thenodemaster in post First Homemade Pen Blank
Nice save! I like the interesting ...
11-06-2015
10:39 PM - Bill Boehme quoted thenodemaster in post Deleted Posts
11-04-2015
08:29 AM - Woodychips quoted thenodemaster in post Burls, burls, burls
Would you consider selling one or ...
10-31-2015
05:31 PM - Woodychips quoted thenodemaster in post I have a problem.
My shop is too clean. What should...
10-23-2015
10:28 AM - 9thousandfeet quoted thenodemaster in post Vacuum Pumps
...who mentioned his complaints ab...
10-22-2015
07:00 PM - 9thousandfeet quoted thenodemaster in post Vacuum Pumps
@9kfeet: That was why the set I bo...
10-21-2015
03:41 PM - Bill Boehme quoted thenodemaster in post Vacuum Pumps
I am almost ready to pull the trig...
10-13-2015
06:23 AM - DRoyLenz quoted thenodemaster in post Beginner Pen Turner's Shopping Cart
As for the finish, I use CA and ha...
10-03-2015
02:42 PM - mengtian quoted thenodemaster in post My Revised Plan for Lathe Purchase
Have you looked at Grizzly? That ...
09-30-2015
03:53 PM - epicfail48 quoted thenodemaster in post Well, I made a mess...
I ran out of time last night (just...
10:03 AM - Big Jim quoted thenodemaster in post Howdy node
Well, somebody has been shopping H...
09-25-2015
06:05 AM - toolguy1000 quoted thenodemaster in post Tablesaw Horse Power
It was a cheapy in my book and was...
09-23-2015
01:27 PM - toolguy1000 quoted thenodemaster in post Tablesaw Horse Power
Hello everyone. I am looking into...
10:25 AM - NickDIY quoted thenodemaster in post Tablesaw Horse Power
I am leaning for the 5HP but will ...
09-22-2015
12:38 PM - MT Stringer quoted thenodemaster in post Tablesaw Horse Power
I replaced the freud rip blade wit...
09-01-2015
07:47 PM - Bill Boehme quoted thenodemaster in post Making a silk purse ...
.... The motor I used was a spare...
08-30-2015
09:38 AM - hwebb99 quoted thenodemaster in post Electric motor lathe build
I had the 12"x33" harbor freight l...
08-29-2015
02:33 PM - Bill Boehme quoted thenodemaster in post Electric motor lathe build
I had the 12"x33" harbor freight l...
 
For the best viewing experience please update your browser to Google Chrome