Woodworking Talk - Woodworkers Forum - View Profile: JIMMIEM

JIMMIEM JIMMIEM is offline

Senior Member

  Statistics

Total Thanks
General Information
  • Last Activity: Yesterday 01:18 PM
  • Join Date: 10-12-2014

  Mentions

07-24-2020
05:25 PM - JIMMIEM mentioned [email protected] in post Newbie needs advice
[email protected] I have an older Cra...
07-23-2020
09:45 AM - JIMMIEM mentioned Tool Agnostic in post Need New Circular Saw
... you do with it? Tool Agnostic Yes..right blade, c...
08:19 AM - JIMMIEM mentioned johnedp34 in post Need New Circular Saw
johnedp34 I've read a lot of ...
06-29-2020
08:42 AM - JIMMIEM mentioned Echo415 in post Trim Question
...of a multi tool. Echo415.....the real questio...
06-28-2020
11:50 PM - Echo415 mentioned JIMMIEM in post Trim Question
JIMMIEM Not necessary with a...
08-19-2018
12:46 PM - Student mentioned JIMMIEM in post Please advise a newbie about rail and stile router bits
JIMMIEM, thank you for telli...
06-08-2018
02:16 PM - GreyhoundGuy mentioned JIMMIEM in post Best After Market Fence & Rail System?
...r the replies, all. JIMMIEM, hawkeye10, and Mayl...
06-25-2016
05:57 PM - Darkk Helmet mentioned JIMMIEM in post Capping oak steps - need advice
...emaining pieces. JIMMIEM I have not looked in...

  Quotes

08-12-2020
11:10 AM - GeorgeC quoted JIMMIEM in post How rigid is the 24" max drawer width listed limit on drawer slides?
I have used a lot of KV 8400...
08-08-2020
10:13 PM - allpurpose quoted JIMMIEM in post Cabinet dilemma
If you've a lot of 3/4" plyw...
08-07-2020
02:54 PM - Lakewood Brian quoted JIMMIEM in post Stack of MDF sheets = flat reference surface?
While on the subject of auxi...
07-25-2020
10:58 PM - scott67 quoted JIMMIEM in post picking lumber from home center
Plywood for the top and bott...
05:27 PM - rvi17 quoted JIMMIEM in post How to cut a straight clean groove? Uber beginner
There are a few router bits ...
03:19 PM - rvi17 quoted JIMMIEM in post How to cut a straight clean groove? Uber beginner
WOW! Thank you all so much f...
07-24-2020
05:46 PM - woodnthings quoted JIMMIEM in post OK, a groove will have a rounded bottom .....
My first choice would be a r...
07-07-2020
03:04 PM - Tool Agnostic quoted JIMMIEM in post Anyone ever built their own coffin?
We recently went to prearran...
12:55 PM - _Ogre quoted JIMMIEM in post Anyone ever built their own coffin?
I told my wife to leave me a...
11:58 AM - Tool Agnostic quoted JIMMIEM in post Anyone ever built their own coffin?
Don't you have to be in some...
07-02-2020
05:11 PM - woodnthings quoted JIMMIEM in post Maybe so, but ......
If the treads are a minimum ...
06-27-2020
12:42 PM - _Ogre quoted JIMMIEM in post Trim Question
An oscillating multitool. Us...
06-07-2020
08:26 AM - Bbop352 quoted JIMMIEM in post Need some advice on how to achieve this joint
Biscuits could also be used ...
06-04-2020
10:28 PM - _Ogre quoted JIMMIEM in post Need help upgrading/rebuilding my bathroom cabinets
Not sure how it will hold up...
05-30-2020
09:20 AM - Tool Agnostic quoted JIMMIEM in post Silly Observation about Lifetime Carbide Router Bits
Yes. If you look under the ...
07-13-2019
08:26 AM - Auggie quoted JIMMIEM in post Fence Recommendations for vintage Craftsman 113 TS
I have the Delta T2 fence in...
07-07-2019
02:59 PM - Pineknot_86 quoted JIMMIEM in post Reworking stairway
I had done some and used bis...
06-15-2019
07:20 PM - Dylan JC Buffum quoted JIMMIEM in post Table Top glue up.
When the glue is applied the...
03-07-2019
09:06 PM - Tom-G quoted JIMMIEM in post DIY Mobile Base or Store Bought?
I just bought one from Harbo...
02-23-2019
05:49 PM - woodnthings quoted JIMMIEM in post mathematically possible, so sure try it ......
I have a DeWalt DW618 router...
 
For the best viewing experience please update your browser to Google Chrome