Woodworking Talk - Woodworkers Forum - View Profile: DrRobert

DrRobert DrRobert is offline

Senior Member

  Statistics

Total Posts
Total Thanks
General Information
  • Last Activity: Today 01:29 PM
  • Join Date: 04-27-2015

  Mentions

01-20-2020
11:01 PM - Tool Agnostic mentioned DrRobert in post Question about format on reply
(Post deleted, please ignore....
11-30-2019
11:01 AM - bob493 mentioned DrRobert in post Screws in Hard Wood, 101
DrRobert necessary vs easier ...
11-14-2019
07:06 PM - bob493 mentioned DrRobert in post Rebuilding Table Saw
... speak of here? DrRobert -> All testing is do...
03:07 PM - carlrez mentioned DrRobert in post Is Pine ok to use for a cutting board?
...limited budget. DrRobert - Being a resinous w...
11-11-2019
12:36 PM - carlrez mentioned DrRobert in post Band Saw setup/tuning guide
...luing anything. DrRobert Thank you for your f...
10-22-2019
05:27 PM - mmejia27 mentioned DrRobert in post Deleted Posts
09-30-2019
10:38 AM - DrRobert mentioned woodnthings in post Pros and Cons of Jobsite Table Saws for Serious Woodworking
woodnthings - no I'm not trollin...
09-19-2019
10:28 AM - DrRobert mentioned woodgeek in post Ridgid r4512 vs SawStop JobSite Pro & Contractor
...n't redundant, but @woodgeekness, you are well ad...
09-04-2019
10:28 AM - DrRobert mentioned woodnthings in post Squaring on a table saw
@woodnthings: All I'm saying is ...

  Quotes

03-25-2020
01:29 PM - epicfail48 quoted DrRobert in post Cutting aluminum
Epic's got it right. You can...
10:28 AM - GeorgeC quoted DrRobert in post Cutting aluminum
Epic's got it right. You can...
03-24-2020
11:29 AM - 253wood quoted DrRobert in post Battens needed or not? Reclaimed fir table top
With that wood and thickness,...
11:06 AM - woodnthings quoted DrRobert in post This isn't a typical hole saw .....
I think the cutters are rever...
10:30 AM - NLarson801 quoted DrRobert in post How would you tackle this?
It can be done with solid woo...
03-23-2020
01:11 PM - FrankC quoted DrRobert in post Router Bit for Miter Slots?
T-track type slot cutters are...
03-18-2020
05:55 PM - audiofanman quoted DrRobert in post Intro and dissimilar expansion rate techniques ?
I don't think you'll have any...
12:24 PM - woodnthings quoted DrRobert in post I like this idea ...
Hi Anderjack If you want to r...
03-16-2020
06:35 PM - audiofanman quoted DrRobert in post Intro and dissimilar expansion rate techniques ?
I don't think you'll have any...
03-09-2020
05:26 PM - epicfail48 quoted DrRobert in post What's the correct method to join these?
I totally agree with this alt...
03-04-2020
09:34 AM - woodnthings quoted DrRobert in post Good advice ....
Generally speaking . . . To...
03-02-2020
12:52 PM - difalkner quoted DrRobert in post Inlay wood
X2 on Constantine's. I found ...
02-27-2020
11:28 PM - Scurvy quoted DrRobert in post Sanding out scratches made from sander.
Stop and take a deep breath. ...
02-26-2020
11:32 AM - Bill4807 quoted DrRobert in post Desk flat oak top
. In your situation, I sugges...
02-18-2020
10:02 AM - RickKr quoted DrRobert in post Tapering a thin piece
A drum sander would be the be...
02-13-2020
01:08 PM - FrankC quoted DrRobert in post If you only had one woodworking tool?
An axe. Because if I only ...
02-11-2020
06:53 PM - epicfail48 quoted DrRobert in post MDF Safety
Yes, MDF dust is horribly dan...
02-07-2020
10:41 AM - RickKr quoted DrRobert in post URL Please
Offset will work best I think...
04:51 AM - Daniel Lombardo quoted DrRobert in post Radial Arm Saw with Miter saw Placement
It should work out fine. I...
12:37 AM - [email protected] quoted DrRobert in post Crosscut Sled Question
Offset will work best I think...
 
For the best viewing experience please update your browser to Google Chrome