difalkner difalkner is offline
- About difalkner
- Former professional woodworker
- NW Louisiana
- Guitar, music, computer, cooking, photography, golf
- Woodworking, CNC owner/operator, Luthier wannabe
- Total Albums: 2
- Total Pictures: 18
- Albums Created by difalkner
- Total Messages: 11
- Most Recent Message: 05-29-2019 09:33 AM
- Visitor Messages for difalkner
- Last Activity: Today 11:33 AM
- Join Date: 11-27-2011
|11:56 AM - Cricket mentioned difalkner in post
|09:56 PM - Reggi Williams mentioned difalkner in post Need some help or suggestions.
... welcome. To answer difalkner the photos I posted ...
|01:16 PM - Cricket mentioned difalkner in post
|05:06 PM - shoot summ mentioned difalkner in post Unisaw build thread
...nding out about difalkner's Powermatic 66 resu...
|07:42 AM - difalkner mentioned Tennessee Tim in post Is my air-dried ash any good?
Hi Carolyn - Tennessee Tim is the guy to ask on...
|12:53 PM - difalkner mentioned Alexa Lou in post Hand held circular saw keeps stopping?
... the forum, Alexa! Alexa Lou - Are you planning o...
|12:19 PM - difalkner mentioned Steve Neul in post Anybody know about Mohawk Products?
...r polishing. Maybe Steve Neul can chime in to assi...
|08:50 PM - difalkner mentioned Cricket in post For Cricket,Painfully Slow
...ved to Site Help so Cricket will see this more e...
|11:53 AM - difalkner mentioned MT Stringer in post
|12:57 AM - WeebyWoodWorker mentioned difalkner in post Inspiration needed
...e ideas. :smile2: difalkner These guys just keep...
|03:04 PM - WeebyWoodWorker mentioned difalkner in post Retired - Finally and time to "wood out"
...orking CLICK HERE difalkner That's straight up s...
|01:10 PM - Tool Agnostic mentioned difalkner in post Finish for a cutting board
difalkner's suggestions are ve...
|05:56 PM - difalkner mentioned Kenbo in post Howdy from So. Cal.
...when you're ready. Kenbo is a very good scrol...
|03:19 PM - souwleye mentioned difalkner in post Live edge slab, is this bark?
...ttom of the form difalkner, thanks a lot! ill u...
|01:21 PM - GreyhoundGuy mentioned difalkner in post App too draw blueprints
I agree with difalkner and mackman. Sketch...
|05:23 PM - Catpower mentioned difalkner in post New with a question
...if I can get David @difalkner attention, he is pre...
|06:43 PM - woodnthings mentioned difalkner in post The bridge fits in there?
...idge. Our Moderator difalkner may have some sugges...
|12:08 PM - Cricket mentioned difalkner in post
|03:08 PM - difalkner mentioned Jig_saw in post Wood machining or woodworking?
...t. I do agree with Jig_saw about losing the abi...
|11:04 AM - difalkner mentioned Kenbo in post Scroll saw research
Get with Kenbo - he's a master at t...
|05:45 PM - Christofix quoted difalkner in post Jig on the crosscut sled to make dowels
Welcome to the forum! Add you...
|05:29 PM - Steve Neul quoted difalkner in post
|11:39 AM - BigJim quoted difalkner in post
|11:35 PM - BigJim quoted difalkner in post
|04:45 PM - BigJim quoted difalkner in post
|05:23 PM - landman quoted difalkner in post Which maple is it?
Curly, mild, but pretty. Da...
|07:49 AM - [email protected] quoted difalkner in post Autographs on a guitar
Which wood and how figured is ...
|07:47 AM - [email protected] quoted difalkner in post Autographs on a guitar
Which wood and how figured is ...
|03:59 PM - Mark Jones Ozark quoted difalkner in post internet to my shop
How long is the run to the sho...
|08:11 PM - Steve Neul quoted difalkner in post Yonico router bits.
If the bit was for 3/4" materi...
|03:48 PM - woodnthings quoted difalkner in post Appearances in the photos....
The key is flat and just fits ...
|11:08 AM - LRM quoted difalkner in post Looking for some info
We have a CNC but for detailed...
|05:51 PM - Steve Neul quoted difalkner in post Help! "degree in woodworking"
There's a line in the film whe...
|08:16 AM - Steve Neul quoted difalkner in post
|10:25 PM - Steve Neul quoted difalkner in post
|07:50 PM - Steve Neul quoted difalkner in post
|04:02 PM - Yonathan quoted difalkner in post Adding a “gripping area” to a cutting board
Since it's not end grain you w...
|02:02 PM - shoot summ quoted difalkner in post Unisaw build thread
That's a pretty cool idea. I'...
|12:14 PM - Ken Johnson quoted difalkner in post Cutting Board Help
I didn’t look that close...
|12:27 PM - hawkeye10 quoted difalkner in post Choosing a Lathe
The fit and finish on our Lagu...