Woodworking Talk - Woodworkers Forum - View Profile: ajdragon

ajdragon ajdragon is offline

Senior Member

  Visitor Messages

Showing Visitor Messages 1 to 1 of 1
  1. workthewood
    11-15-2018 08:19 PM - permalink
    workthewood
    I'm not sure you got my private message to you so here goes: Thanks again for creating a video of replacing bearings on your Craftsman #103.23340. I have one further question. I checked for co-plane and my infeed table takes a .025" nose dive toward the cutter head and is equal right to left. I would like to remediate this, if I can. Can I shim it or play with those monster bolts underneath to take up the difference? Some one told me a jointer is only as good as its co-plane. Detail instructions would be great. Thanks.

  Statistics

Total Posts
Visitor Messages
Total Thanks
General Information
  • Last Activity: 09-19-2019 01:00 AM
  • Join Date: 07-26-2017

  Mentions

No results to display...

  Quotes

08-28-2019
05:29 PM - Sleeper quoted ajdragon in post Looking for nondestructive Nail puller
Your more of a man then me, I...
08-22-2019
01:20 AM - Tool Agnostic quoted ajdragon in post Craftsman wet/dry vac Question
Hi. Well I got a hose, and no...
07-22-2019
06:30 PM - woodnthings quoted ajdragon in post OK, it ain't my fingers, but ...
I hope there is no way it can...
07-20-2019
11:35 AM - Tool Agnostic quoted ajdragon in post Miter Saw Blade Guard
Hi I was wondering what you...
07-19-2019
02:44 PM - TimPa quoted ajdragon in post Miter Saw Blade Guard
Hi Is it supposed to retr...
07-15-2019
09:11 AM - gj13us quoted ajdragon in post Miter Saw Blade Guard
Hi I'm doing sub floor repa...
04:14 AM - woodnthings quoted ajdragon in post There's a middle ground .....
Hi I'm doing sub floor rep...
05-30-2019
07:35 PM - unburled quoted ajdragon in post 90 deg vs bevel blade alignment on table saw
I think I understand what Unb...
03-09-2019
10:09 PM - Jim Frye quoted ajdragon in post My Tool Triggered Switch Is Dying...
Hi It sounds like the rela...
02-21-2019
01:24 AM - Reinout quoted ajdragon in post Lathe 'play' along spindle axis
Proper set screws will bite i...
02-15-2019
09:03 AM - BTracy138 quoted ajdragon in post Drill press quill not moving...
Hi I'm saving lead so I ...
02-14-2019
09:25 PM - BTracy138 quoted ajdragon in post Drill press quill not moving...
Hi Now you just need to cle...
02-11-2019
03:29 AM - BTracy138 quoted ajdragon in post Drill press quill not moving...
Hi Try doing this. Two or t...
02-10-2019
10:20 PM - BTracy138 quoted ajdragon in post Drill press quill not moving...
Hi The C clip is located un...
12:37 PM - BTracy138 quoted ajdragon in post Drill press quill not moving...
Hi It looks like a snap ...
12:09 PM - BTracy138 quoted ajdragon in post Drill press quill not moving...
Hi Have you tried taking...
12-26-2018
10:23 PM - Sleeper quoted ajdragon in post Any video training recommendations for Compound Miter Saw?
Hi Here's another video....
12-17-2018
02:55 AM - PTC01 quoted ajdragon in post Delta Rockwell 34-500 8" table saw bearings
Hi Here's two videos. Del...
12-16-2018
05:57 PM - 13579 quoted ajdragon in post Question about Cleaning Cast Iron Wings
I would suggest electrolysis....
12-15-2018
10:44 AM - Catpower quoted ajdragon in post Craftsman 100 electrical problem
Hi I can start the motor if...
 
For the best viewing experience please update your browser to Google Chrome