Woodworking Talk banner

Newbie Dovetail Question...

4K views 23 replies 15 participants last post by  Chris Curl 
#1 ·
I am jumping from site to site, blog to blog, article to article, and contraption to contraption looking for the easiest, most economical way to make dovetail joints.

I eventually want to learn to make them by hand but at the moment I don't have the time for that endeavor.

I need to make a few drawers with dovetail joints and am kinda in a pinch as far as finances are concerned so I'm looking to learn to do them quick, easy and for as little as possible.

If this is at all possible I'm sure you guys can help me out, and if it's not... you'll let me know that too.
 
#2 ·
They really aren't that hard to cut by hand and if finances are an issue, all you need is a dovetail or gents saw and a chisel or two. With an hour or two of practice you could be cutting your drawers. Total cost~ $30-100 depending on what type of saw and chisels you buy. If that's the choice you make there is lots of help available here and many previous tutorials have been posted as well.

Sorry, but I can't help you with choosing a jig, I've never used one, but many others have and I'm sure many will give you some options.
 
#3 ·
Ditto on the preceding post. Making dovetails by hand is satisfying and not as hard as people make it out to be. Of course picture-perfect joints will take practice, but you can make structurally sound joints on your first attempt. I'm still relatively new at this, but I recently completed my third dovetailed project and was very happy with the result. The first two looked like bad dental work, but they still served their intended purpuse. I paid $10.99 for a dovetail saw at Ace Hardware and it works fine. Of course you will also need a couple of chisels at around $20 each, a sharpening system of some kind, a square, and a sliding bevel. That's all you really need.
 
#5 · (Edited)
I bought a Veritas dovetail saw which cost $90 but has helped immensely with both dovetails and tenons, and is easier to control than the straight handle dovetail saws. I spent a good bit on Veritas honing guide Norton water stones, and a flattening stone but have used all of that at least weekly on chisels and my hand plane irons.... my point being it may be pricy but you will use all of it for much more than just dovetails, and you will have a need for it if you're aspiring to hand cut dovetails and the like.

by the way beginners tip.... to keep the saw from wondering off your dovetail marks use a chisel, a mallet, and a few taps on the scored lines. The saw will ride in that groove and helps keep you on target. Once I got that part down I was easily making great dovetail joints. Check out the many youtube vids and you'll be doing it in no time.
 
#8 ·
I am jumping from site to site, blog to blog, article to article, and contraption to contraption looking for the easiest, most economical way to make dovetail joints.

I eventually want to learn to make them by hand but at the moment I don't have the time for that endeavor.

I need to make a few drawers with dovetail joints and am kinda in a pinch as far as finances are concerned so I'm looking to learn to do them quick, easy and for as little as possible.

If this is at all possible I'm sure you guys can help me out, and if it's not... you'll let me know that too.
There are SO many alternatives.... That said have you considered a couple of shop made jigs, one ffor tails made on the tablesaw and pins using the router table? If you have access to either Wood, Fine woodworking,
or youtube there are many examples there. Hope this is of help.
 
#9 ·
a router and a dovetail jig ($100 or so) will work well for half blind dovetials. you'll have to spend a few hundred to get through dovetails. there is a learning curve on the machine/setup. but once accomplished you can make many dovetails fast. i use porter cable 4212 i think.
 
#10 ·
Thanks for all the replies.

I think that I'm going to try my hand at making the dovetails by hand.

I always seem to be a little more proud of things that I made by hand, not that it will matter to most, but I can still say I made those dovetails by hand. Every once in awhile I'll come across someone that
can appreciate the task and admire my craftsmanship.

THat's n ot to say that if I have to crank out a bunch in a hurry I won't go the jig route. I was thinking about going with the tablesaw jig. That looked pretty intersting and worked efficient enough.

I'll keep everyone posted on my progress (if you guys want)
 
#12 ·
Alright, took a shot at my first set of hand cut dovetails...

Let me preface this by saying I used a template I found online, I didnt use tools that were even close to being the right tools for the job and I rushed through the entire process.

While the DTs are atrocious, I am hooked. A trip to the store tomorrow to get the appropriate tools and I'm going to go nuts learning how to rock these things out.

The one thing I'm not really clear on is the layout, I've watched a bunch of videos and done some reading but for some reason it's not sinking in. Any advice??

What thickness of wood is best? easiest to learn with??
Is poplar ok?
 
#14 ·
I think poplar is fine. It's easy to cut and cheap. I don't know if there is a correct thickness to learn on. I'd choose whatever is cheapest ( probably a 1x6) and start practicing - but I wouldn't go any thinner than 1/2".

After each set of dovetails, just cut the boards flush and you're good to go. I'd keep the dovetails you practice on intact so you can refer to them and make corrections for the next set.

As for layout, I wouldn't worry too much about that right now. Focus more on cutting and marking technique and when you are comfortable cutting them you can decide what style you like. A lot of times I'll decide on a dovetail thickness/spacing and measure from each outside edge of the board leaving a thinner (or thicker) tail in the middle - whatever is left is what I get. Other times I'll measure and calculate for evenly spaced/sized tails across the width. You can also start measuring from the middle working out in each direction leaving the outside most tails a different size.

You can also change the size ratio between pins and tails. Sometimes I'll mark the pins to be the same width as the tails, sometimes I'll use large tails with really thin pins. Probably the best thing to do while you are practicing and learning is to keep the tails and pins the same size.

Also, if you haven't already take a look at some of the tutorials that have been posted here. Billy De posted one about a year ago that was really good. It was full of great tips for the whole process from marking to final fitting of the joint. It's here.
 
#16 · (Edited)
Poplar is a great choice. Thickness is personal preference, but starting out IMO 3/4" is a good place to start. Re tails or pins first, there are many opinions, but another good starting point would be tails first, then mark the mating board for the pins. Remember to do your tail board layout to have half pins on both sides of the pin board, ( don't ask me how I know this...) . As many have said here, there are many examples of the process out on the net. Good luck, and I look forward to seeing your efforts!
 
#21 ·
Good to hear your going to try cutting them by hand, like said already it really isn't that hard just take your time doing the marking and cutting. I have another thread going here in the Joubert section showing my progress at cutting them by hand and in a few hours a night over four nights I'm getting great results, if I can do it so can you. Buggers tip I can give is set yourself up in a comfortable position at your bench and take your time, and post pics so we can all see your progress.

pit bulls rock!
 
#22 ·
the dude said:
Good to hear your going to try cutting them by hand, like said already it really isn't that hard just take your time doing the marking and cutting. I have another thread going here in the Joubert section showing my progress at cutting them by hand and in a few hours a night over four nights I'm getting great results, if I can do it so can you. Buggers tip I can give is set yourself up in a comfortable position at your bench and take your time, and post pics so we can all see your progress.

pit bulls rock!
Stupid auto correct, meant to say joinery section lol...Joubert, what the heck is Joubert?

pit bulls rock!
 
#23 ·
These were the first ones I cut by hand that worked right, and I have a confession to make: I screwed up them up every time until I stopped pre-marking.

I do tails first, and I mark them only on the end grain and for the depth of cut. Then I have my lines straight across the end grain to line up the saw, and I cut the angles by eye. I still have the first joint I did that way: it's a piece of 1x4 with a single tail, and with no glue I haven't broken it apart yet. All the ones I pre-marked wound up off the line, and I spent ages trying to "fix" the angle when it didn't really matter. I now cut the tails as I said, pretty much by eye, and then mark the pins off the cut board.

I'm not saying this is the best way to do it, or the only way to do it, or anything like that, but I'm always amazed by people who can mark their dovetails, cut them, and come out near the line. Just doesn't work for me. (Yeah, I'm weird. I know.)
 
#24 ·
that is the way paul sellers does them too, so you are in good company.

he cuts the tails first, then transfers the profiles to the end of the other board for the pins.

if i practice it enough, maybe i will be able to do them 1/2 as well as he can. there is a video where he makes all 4 joints for a box in under 10 minutes. that is the video i linked to earlier in this thread.
 
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top