How much is Delta 36-600 TS worth? - Woodworking Talk - Woodworkers Forum

Thread Tools Display Modes
post #1 of 5 Old 10-05-2010, 04:27 PM Thread Starter
Join Date: Jul 2010
Posts: 34
View borisw37's Photo Album My Photos
How much is Delta 36-600 TS worth?

Found a listing on craigslist for a Delta 10" Table Saw Model # 36-600
Assuming that its in good condition how much is it worth?
Don't think that model is sold new anymore but does anybody know what it used to sell for?

Thank you,

borisw37 is offline  
Sponsored Links
post #2 of 5 Old 10-05-2010, 05:39 PM
sweensdv's Avatar
Join Date: Mar 2008
Location: WI
Posts: 600
View sweensdv's Photo Album My Photos
Isn't that the model that was basically a direct drive benchtop table saw with a leg stand? If so then $50-$75 would be in the ballpark.


Life is like a roll of toilet paper.
The closer it gets to the end, the faster it goes.
sweensdv is offline  
post #3 of 5 Old 10-06-2010, 05:45 PM
Senior Member
firehawkmph's Avatar
Join Date: Apr 2008
Location: Near Cleveland, Ohio
Posts: 4,821
View firehawkmph's Photo Album My Photos
Here's a pic of a 36-600. I had an older version of this that I sold this year for $200.00. Mine was made in the US, along with having a baldor motor, which is the way if came from the factory. I sold it to a buddy for the 200. I think it was worth more than that. Good solid saw. The ones made in recent years I don't think were built the same. First pic is a recent one. Second pic is my saw I sold.
Mike Hawkins
Attached Thumbnails
Click image for larger version

Name:	delta 36-600.jpg
Views:	4414
Size:	98.3 KB
ID:	17219  

Attached Images
firehawkmph is offline  
post #4 of 5 Old 10-06-2010, 10:41 PM
No Longer Here
Join Date: Nov 2007
Posts: 5,465
View knotscott's Photo Album My Photos
Mike - Your Rockwell looks to be a full size belt drive contractor saw. The 36-600 is more of a downsized compact contractor saw "look-a-alike" (only 22"d instead of 27"d, and is 38"w vs 40"+ of a full size saw). They weigh in ~ 150# vs 250# of a full size saw, and have a 15 amp universal motor. It later became the TS300 and retailed in the $300 range.

Depending on condition, it might be worth $100 or so, but they tend to be cost prohibitive to fix if the motor kicks the bucket. FWIW, my 36-600 did everything I asked of was a little loud, and a little lightweight, but wasn't a bad saw.

Last edited by knotscott; 10-28-2010 at 05:46 PM.
knotscott is offline  
post #5 of 5 Old 10-28-2010, 03:16 PM
Junior Member
Join Date: Oct 2010
Location: Richmond, VA
Posts: 19
View In-com-plete's Photo Album My Photos
I have the 36-600. Bought it about a year ago for $100. A guy I work with just bought one 2 weeks ago and he paid $200 for his.

I think it's a good saw. Although it's the only tablesaw I've ever had and the 2nd I've ever used. It is very loud but I think it's worth the $100 I paid for it. I don't think it's worth more than $150. Mainly because of the 22" top. That was actually a plus when I bought the saw as I was working in a small shed. But now, having a larger work area, I wish I had bought a saw with a larger top.
Attached Thumbnails
Click image for larger version

Name:	36-600.jpg
Views:	3214
Size:	99.2 KB
ID:	17596  

In-com-plete is offline  

Quick Reply

Register Now

In order to be able to post messages on the Woodworking Talk - Woodworkers Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode

Similar Threads
Thread Thread Starter Forum Replies Last Post
using aftermarket knife setting jigs for Delta RC-33 or Invicta/Delta 22-650 Terrance L. Maloney General Woodworking Discussion 16 01-21-2013 08:45 PM
Worth a Look rrich Off Topic 6 05-06-2010 10:21 AM
Do you think this is worth trying it out? John in Tennessee Power Tools & Machinery 3 10-06-2009 12:45 PM
Here's my 2 worth . . . TexasTimbers Off Topic 8 08-19-2009 08:57 PM
Is it worth it? werneb01 Forestry & Milling 3 03-18-2009 08:44 PM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

For the best viewing experience please update your browser to Google Chrome